PURA-NATURA HDE 52-0
PURA-NATURA HDE 52-0 impresses with its dull matt natural wood effect, so that the natural appearance of the wood is retained. The surface offers high scratch resistance with very good resistance to footprints and common household chemicals. The brightening and light fast 2C top coat is suitable for priming and top coating light-colored woods and is particularly suitable for stairs and wooden floors thanks to its DIBt approval. For parquet and wooden floors with a tendency to side and block gluing, the combination with the brightening primer HG 21 or with the scorching primer HG 22 is recommended.
Enquire articlePage content
- Light-fast
- Dull matt with good scratch resistance
- Natural wood effect
Processing
- 2C line
Airless
-
Airless low pressure
Airmix
Compressed air spraying
Rolling
Spreading
Areas of application
In living areas, and also in higher strain areas of parquet and wooden flooring. Can also be used on bleached surfaces (that are adequately dry).
Technical information
Sustainability data sheet
Certificates
Technical Specifications
| Proportion of renewable raw materials % | 0 % |
|---|---|
| Appearance | colourless |
| Decopaint base | wb |
| Decopaint category | J |
| VOC EU % | 6 % |
| Number of layers (max) | 2 |
| Quantity per layers (min) | 80 g/m² |
| Quantity per layers (max) | 100 g/m² |
| Total quantity applied | 200 g/m² |
| Mixing ratio (volumetric) | 10 : 1 | Hardener: HDR 72 |
| Mixing ratio (gravimetric) | 100 : 10 | Hardener: HDR 72 |
Processing Instructions
| Potlife | 3 h / 20 °C |
|---|---|
| Drying | 3 h / 20 °C |
| Due to hardening | 7 d / 20 °C |
| Surface sanding (grain size) | 100 - 120 |
| Intermediate sanding (grain size) | 120 - 150 |
| Yield per pass | 9 - 10 m²/l |
| Processing information | The floor must first be sanded back to the bare wood and be dry and free from oil, grease, wax, silicones and sanding dust. Shake the lacquer well! Add the correct hardener to the organic lacquer container and immediately shake well for 1 - 2 min. Do not mix in the application container. The mixing ratio must also be accurately observed in the case of partial amounts, and the mixture well shaken. Press the strainer into the outlet opening, fill the lacquer / hardener mixture into a suitable application container and work from this! Only use a mixture within the given application time. Never store product mixed with hardening agent in closed containers. Do not use any electrical stirring devices; risk of forming foam or bubbles! |
| Special notes | Greying may occur on dark woods or stains because of the light milky colour of the products.. In order to reduce the risk of lateral bonding, critical substrates such as wood plaster, edge lamellae, floor boards, parquet on underfloor heating, etc. require an appropriate pretreatment with HG 21 or HG 22. If using particularly tannin-rich woods, we recommend using basecoat HG 22 or HG 24. To avoid the possibility of staining, please only renovate parquet flooring, which was previously treated with solvent-based systems, with solvent-based systems again! Shake the lacquer well! Spraying: possible; however the addition of water is required. When the hardening agent is well worked in, adjust the spraying viscosity with up to 5 % water. Personal protective equipment and adherence to the instructions for the spraying application. Press the strainer into the outlet opening, fill the lacquer / hardener mixture into a suitable application container and work from this! Only use a mixture within the given application time. Never store product mixed with hardening agent in closed containers. Do not use any electrical stirring devices; risk of forming foam or bubbles! Clean work equipment with water. Dried lacquer residue can be removed with Hesse CLEANING-AGENT DV 9. Films or carpets must not be placed on the parquet flooring until it has completely hardened.The maximum application amount in wet film when using this product as a flame retardant coating material for seagoing vessels is] 2 x 100 g/m². The coating with this product meets the requirements of abrasion class 2B according to DIN 68861 as well as the adhesive strength GT 0 according to DIN EN ISO 2409. |
Procedure example
Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.
Request a series
<% headline %>
Your request for the article
PURA-NATURA HDE 52-0Your request for the series
PURA-NATURA HDE 52-0
