HYDRO-PU Glass lacquer satin effect HDU 57120
The HDU 57120 is an isocyanate-freeclear and light fast HYDRO-PU glass lacquer that has been specially developed for glass coating in the spraying process. You receive a waterproof and scratch-resistant glass lacquer surface with the desired satin effectwhich is also highly resistant to chemical and mechanical stress.
Enquire articlePage content
- isocyanate-free
- light fastness
- Surface with satin effect
Processing
Compressed air spraying
-
other treatment
Areas of application
In the complete field of interior fittings, including in kitchens and bathrooms. Tinting with the likes of BP Colour concentrates is possible.
Technical information
Sustainability data sheet
Certificates
Technical Specifications
| Proportion of renewable raw materials % | 0 % |
|---|---|
| Appearance | not relevant |
| Decopaint base | wb |
| Decopaint category | J |
| VOC EU % | 5,4 % |
| Number of layers (max) | 1 |
| Quantity per layers (min) | 100 g/m² |
| Quantity per layers (max) | 150 g/m² |
| Total quantity applied | 150 g/m² |
| Mixing ratio (volumetric) | 100 : 3 |
| Mixing ratio (gravimetric) | 100 : 3 |
Processing Instructions
| Drying | 24 h / 20 °C |
|---|---|
| Due to hardening | 7 d / 20 °C |
| Surface sanding (grain size) | |
| Intermediate sanding (grain size) | |
| Yield per pass | m²/l |
| Processing information | Substrate preparation is decisive to the bond of the glass coating. The glass surface to be coated must be clean and grease-free. Carefully clean the glass surface prior to application, e.g. using Glass cleaner HS 6601. Before processing, add the crosslinker in the indicated ratio while stirring and ensure that it is well incorporated. Note the limited processing time. Setting material can continue to be used by mixing with fresh material and then adding the crosslinker. Clean tools with water. Use HYDRO Cleaning agent HV 6917 to remove dried lacquer residues. In the event of combined coatings (HYDRO and solvent-based lacquers) rinse application tools using HYDRO Reversing agent HV 6904. Add the crosslinker slowly whilst stirring and then adjust the spray viscosity by adding water or HYDRO Optimizer HZ 70, if required. Maximum additive volume 5 %. <p class="MsoNormal"/> A single-coat application at 100 - 150 g/m² on a carefully prepared glass surface is recommended. |
| Special notes | Final hardness of the coating is achieved after one week in correct storage conditions (at least 20 °C room temperature). Always seal opened containers light-tight and air-tight to prevent skin forming. Remove dried lacquer residue using a sieve. Products in containers should be sieved before application. Please build up a full trial coating on the original glass under real conditions. The glass colour can affect the later colour tone when coating behind glass. Please take this into account in selection of the glass! Tinting at 5 - 10 % using our BP Colour concentrates prior to adding the crosslinker enables a coloured, glazing satin effect to be achieved. It should be noted in this regard that the lacquer application quantity, the type of application method and the drying conditions all influence the effect and the colour shade of glass coatings. |
Procedure example
Our technical information is continually adapted to keep up to date with the latest technology and statutory regulations. The latest version is always available online at www.hesse-lignal.de or talk to your local account manager. This information is for advice and is based on the best knowledge available and careful research in line with the current state of the art. This information cannot be held as legally binding. We also refer you to our terms and conditions of business. Safety data sheet is provided in accordance with EC regulation no. 1907/2006.
Request a series
<% headline %>
Your request for the article
HYDRO-PU Glass lacquer satin effect HDU 57120Your request for the series
HYDRO-PU Glass lacquer satin effect HDU 57120
